Ecuador alone exported 377.3 million boxes of bananas in 2025, 3.45 percent more than in 2024, according to the exporters' association ACORBANEC: 30.7 percent to the European Union, 20.3 percent to Russia, 14.9 percent to the Middle East, 11.8 percent to the United States and 7.4 percent to the Southern Cone. Every one of those boxes came from a bunch that spent 10 to 13 weeks inside a polyethylene sleeve. The cover creates a microclimate that raises the mean bunch temperature by about 0.5 °C over 24 hours and by up to 7 °C in the hottest hours, keeps insects, leaf rub and spray drift off the fruit, and shortens the interval from flowering to harvest by 4 to 14 days, according to ProMusa's technical synthesis of Ganry (1975) and Soto (2010). It is the bag with the biggest effect on finger calibre, peel cleanliness and the share of exportable fruit, and also the one most often bought as "the usual" without anyone checking whether the usual was 0.4 or 0.5 mil, 3 mm or pinhole, blue or white.
Manufacturers in Ecuador and Central America publish the trade name and the active ingredient of their impregnated covers but rarely the size, gauge, perforation or weight per cover; the data sheet comes on request. This guide puts those numbers on the table so that you can compare covers from any origin with the same ruler, calculate your farm's consumption and send any manufacturer a complete specification. For gauge selection across the three banana bags (bunch cover, polypack liner and cluster bag) see the micron guide for banana bags (Spanish); for liner and cluster-bag counts per box and per container see banana bags per box and per 40 ft reefer; for the product range see banana bags: bunch covers, polypack liners and cluster bags.
A bunch cover is a polyethylene tube open at both ends (closed at the bottom on some farms), ordered by lay-flat width and length, almost always in inches. The width must clear the first hand without rubbing the fingers; the length must leave 20 to 30 cm below the last hand at harvest, because the bunch keeps growing after bagging. Farms that bag early (before all hands have opened) or that grow 10 to 12-hand bunches therefore order the 90 in tube; farms that bag a formed bunch of 8 to 9 hands use the 72 in tube.
| Lay-flat tube size | Metric | Typical use | Film area per cover | Weight per cover at 10 / 12.7 / 25 µm |
|---|---|---|---|---|
| 34 × 72 in | 86 × 183 cm | Bunches of 8 to 9 hands; bagging a formed bunch; the most-ordered size in El Oro and Los Ríos, Ecuador | 3.16 m² | 29 g / 37 g / 73 g |
| 34 × 90 in | 86 × 229 cm | Bunches of 10 to 12 hands, early bagging, long-bunch varieties | 3.95 m² | 36 g / 46 g / 91 g |
| 32 × 75 in | 81 × 191 cm | Medium bunches; 81.3 cm is the width CORBANA used in its Costa Rican trials | 3.10 m² | 29 g / 36 g / 71 g |
| 36 × 84 in | 91 × 213 cm | Wide bunches of 10 or more hands on high-yield farms | 3.90 m² | 36 g / 46 g / 90 g |
| Tube 80–95 × 140–170 cm | 31–37 × 55–67 in | Common sizes in Central America and the Philippines; ProMusa's reference is a tube 90 cm in diameter and 155 cm long | 2.2–3.2 m² | 21–30 g / 26–38 g / 52–74 g |
Area = 2 × width × length (both faces of the tube). Weights calculated at a polyethylene density of 0.92 g/cm³; perforation removes 1 to 3 percent. Use them to convert covers into kilograms per shipment and per container; the manufacturer confirms the real roll weight.
In Ecuador and Central America gauge is written in mil (thousandths of an inch), for example "0.0004" or "0.4 mil"; in Asia and Europe in microns. The conversion is 1 mil = 25.4 µm. ProMusa places bunch covers at 12 to 25 µm and notes that gauge affects cost and environmental load far more than efficacy; CORBANA tested covers of 10.2 and 12.7 µm and found no productivity difference between low and high density. Covers above 130 µm protect better against cold but cause malformation and sunburn, and are not used in the lowland export zones.
| Gauge | Microns | Weight of one 34 × 72 cover | Covers per 100 kg of film | When it is chosen |
|---|---|---|---|---|
| 0.4 mil (0.0004 in) | 10.2 | 29 g | 3,400 | Lowest cost per cover; linear low-density or high-density resin so it does not tear during placement; the gauge most requested by El Oro farms |
| 0.5 mil | 12.7 | 37 g | 2,700 | Balance of price and strength; the gauge of most impregnated covers in CORBANA's trials |
| 0.6 mil | 15.2 | 44 g | 2,270 | Windy sites or heavy leaf rub; covers reused for 2 or 3 cycles |
| 0.8 mil | 20.3 | 59 g | 1,700 | Reusable and washable covers, highland farms with cold nights |
| 1.0 mil | 25.4 | 73 g | 1,370 | Usual maximum; more heat retention and more cost; the top of ProMusa's reference range |
Two buying rules. First, specify gauge with a tolerance (for example 10 µm ± 10 percent) and ask for the weight per 1,000 covers on the quotation, because it is the simplest way to check that the 0.4 mil cover you receive is not 0.35. Second, at equal gauge, linear low-density polyethylene resists puncture and tearing during placement better than conventional LDPE, which is what allows a farm to drop from 12.7 to 10 µm without more covers torn in the field.
The holes let water vapour out so that relative humidity inside the cover does not reach the point where fungi grow on the fruit; without them the water that condenses on the upper hands scalds the peel. ProMusa describes the standard cover as 2.7 mm holes every 76 mm, with variants of 12.7 mm every 76 mm, 8 or 6 mm every 10 cm, 3 mm and micro-perforation; CORBANA tested 4 and 6 mm. In Ecuadorian purchase orders the specification appears as "3MM" (a hole of about 3 mm in a regular pattern) or "PINHOLE 2MM" (2 mm needle), and local manufacturers advertise "perforations according to the season".
| Perforation | Reference pattern | Effect | Season and site |
|---|---|---|---|
| Pinhole 2 mm | Fine needle, 2 mm, dense pattern (every 25 to 50 mm) | Maximum heat retention, minimum ventilation | Dry, cool season (June to November in El Oro), sites above 300 m, farms trying to shorten the cycle |
| 3 mm (2.7 mm) every 76 mm | Industry standard | Balance of heat and moisture release | Year-round on most farms in El Oro, Los Ríos and Guayas |
| 4 to 6 mm every 76 to 100 mm | Large hole, more open pattern | High ventilation; less condensation and fewer fungal spots | Hot rainy season (December to May), low humid sites, impregnated covers in conventional programmes |
| 8 to 12.7 mm every 76 to 100 mm | Very large hole | Almost no thermal effect; mechanical and insect protection only | Plantain and very hot sites; little used on export Cavendish |
| Partial perforation | Only the lower third perforated | Heat at the top, drainage at the bottom | Farms that bag early with the 90 in tube |
Always specify hole diameter, hole spacing and whether the perforation is full or partial; "perforated" on its own is read differently in every factory. If your farm changes perforation by season, order two references with the same artwork and plan the changeover in the shipment before the season.
The industry mostly uses blue or clear covers; in Ecuador also white, and red or green to separate bagging weeks. Blue covers transmit 73 percent of photosynthetically active radiation and clear covers 93 percent; blue filters ultraviolet and reduces sunburn, with the drawback that it hardens the peel less (ProMusa). What matters before paying more for a colour is that in the most complete trial published in the region, colour changed neither bunch weight nor days to harvest.
| CORBANA trial, Costa Rica, 2010 | Blue | Red | Green |
|---|---|---|---|
| Cover gauge and perforation | 12.7 µm, 4 mm | 10.2 µm, 6 mm (low density); 12.7 µm, 4 mm (high density) | 12.7 µm, 6 mm |
| Useful light transmitted (µmol s⁻¹ m⁻², incident 2,416) | 284 | 240 | 238 |
| Bunch weight, Grande Naine, Matina farm (kg) | 26.6–27.6 | 27.2–28.2 | 27.0–27.6 |
| Bunch weight, Williams, Pococí (kg) | 29.2 | 29.6–30.0 | 29.1–29.4 |
| Days from bagging to harvest, four banana farms | 73.7–86.4 | 73.3–85.7 | 73.6–86.4 |
| Calibre of the central finger, second hand (32nds of an inch) | 44.9–47.5 in all three colours; no statistical difference | ||
| Plantain bunches (Hartón Enano) free of blemish | 46–50 % | 25 % (low) / 72 % (high density) | 19 % |
Source: Vargas, Valle and González, Agronomía Costarricense 34(2), 2010, four experiments on banana and one on plantain, six treatments. The only significant difference appeared in plantain appearance, where green was worst and the high-density red cover was best; on Cavendish banana neither colour nor density had an effect.
With that result, colour is decided for three practical reasons: sun protection (blue or milky white in high-radiation zones), age control (a different colour each week, or white with a coloured ribbon, so the harvester can pick out 11, 12 and 13-week bunches from 20 metres away) and buyer requirement (some certifications and receivers ask for uncoloured film). An association ordering white and red covers of the same size is usually separating bagging weeks or lots from different farms under one logo.
Impregnated covers were developed in the 1970s and carry chlorpyrifos at 1 percent or bifenthrin at 0.1 percent (ProMusa; CORBANA's trial covers were exactly those two types); they control aphids, thrips, moths and beetles without a separate application. In Ecuador they are sold as a farm input registered with Agrocalidad, and local manufacturers offer bifenthrin, bifenthrin plus pyriproxyfen, sulphur or vegetable-oil formulations for organic farms. Three reasons explain why more programmes now ask for untreated covers: the European Union, which takes 31 percent of Ecuador's fruit, set a chlorpyrifos maximum residue level of 0.01 mg/kg; chlorpyrifos was listed under the Stockholm Convention in 2025, which points to restrictions in more markets; and organic fruit, the fastest-growing segment in Ecuador, Peru and the Dominican Republic, does not allow a treated cover. The alternatives are an untreated cover with foam protectors between hands, a cover with botanical repellents (clove, garlic and pepper, per ProMusa) or the impregnated strips that some multinationals insert instead of a treated cover. According to our supplier-selection guide (Spanish), moving from chlorpyrifos to bifenthrin or to an untreated cover added US$0.05 to US$0.08 per box in 2025–2026.
What Fuxing makes: untreated bunch covers in virgin polyethylene with UV additive, in the gauges, perforations and colours of this guide, printed or plain. We do not impregnate covers; if your programme requires a treated cover with an Ecuadorian registration we say so on the quotation and supply the rest of the pack (untreated covers for the organic lots, polypack liners, cluster bags, foam protectors and cartons).
A cover printed with the farm or association name does three jobs: it identifies the fruit in the field and at a shared packhouse, it gives the lot traceability (many certifiers ask for the bunch to be identified from bagging) and it cuts cover losses between neighbouring farms. Printing is flexographic, normally one colour (black, blue or green) on one or two faces, with the artwork repeated every 40 to 60 cm along the tube. What the manufacturer needs: vector artwork (PDF or AI), the Pantone reference or a physical sample, the logo size (usually 10 to 20 cm) and position (one face or both). Every design is a separate reference with its own production minimum, so an association with three farms and two cover colours has six references, and does best to group them in one quarterly shipment.
| Item | Reference specification | Use per bunch | Purpose |
|---|---|---|---|
| Foam bunch protector (EPE polyethylene foam) | Sheet 35 × 50 cm, 5 mm, green, white or blue; also 30 × 40 cm and 3 to 8 mm; called "protectores" in Ecuador and "cojines" or "almohadillas" in Central America | 6 to 10 (one between each pair of hands) | Stops the fingers of one hand scarring the hand below (growth scar) and rubbing on the cover; in untreated programmes it replaces part of the protection of a treated cover |
| "Nun's collar" protector | Low-density polyethylene; US$0.065 per unit in the Technical University of Machala trial | 8 (264 per hectare per week) | Separates the hands and protects the finger neck; the traditional alternative to foam |
| Age ribbon (colour tape) | Polyethylene or polypropylene tape 2 to 3 cm wide, 12 or 13 colours in rotation, one colour per week | 1 | Marks the bagging week; in El Oro harvest is at 12 or 13 weeks and the ribbon tells the cutter which bunches to take |
| Rubber band or plastic tie | Natural rubber band (biodegradable, US$0.0094 per unit in the same trial) or plastic tie | 8 to 10 | Holds the cover and separates the hands; the biodegradable band breaks down between week 6 and week 10 |
Protector and band costs from Palacios Alvarado, Technical University of Machala, 2022 (Santa Inés farm, El Cambio, Machala, El Oro). In that trial, replacing part of the protectors with biodegradable bands raised fingers per bunch from 115 to 135 and the export ratio from 1.11 to 1.23; the Ecuadorian average ratio cited is 0.90, against 1.1 in Costa Rica and 1.4 in Colombia. EPE foam for protectors is made at our Hai Phong plant and travels in the same container as the covers.
Basis: one cover, one ribbon and 6 to 10 protectors per bagged bunch; about 1,600 to 1,800 plants per hectare on export Cavendish and a 50 to 52-week cycle, that is about 33 bagged bunches per hectare per week (the figure recorded in the Technical University of Machala trial was exactly 33). Cover weight for 34 × 72 in by gauge from table 2.
| Farm | Covers per week | Kg of covers per week (10 / 25 µm) | Foam protectors per week (8 per bunch) | Quarterly order of covers (13 weeks + 10 %) |
|---|---|---|---|---|
| 20 ha (small grower) | 660 | 19 / 48 kg | 5,300 | 9,400 covers (0.27 to 0.69 t) |
| 50 ha | 1,650 | 48 / 120 kg | 13,200 | 23,600 covers (0.68 to 1.7 t) |
| 100 ha | 3,300 | 96 / 240 kg | 26,400 | 47,200 covers (1.4 to 3.4 t) |
| 200 ha | 6,600 | 190 / 480 kg | 52,800 | 94,400 covers (2.7 to 6.9 t) |
| Association of 1,000 ha | 33,000 | 960 / 2,400 kg | 264,000 | 472,000 covers (13.7 to 34 t) |
Two consequences for purchasing. First, a 10 µm cover weighs less than half of a 25 µm cover, so sea freight per cover falls in the same proportion; a 40 ft container carries about 8 to 9 tonnes of covers on rolls, that is about 35 weeks of a 100-hectare farm at 25 µm or more than 80 weeks at 10 µm, which is why medium-sized farms buy better in a consolidated container with polypack liners, cluster bags, protectors and cartons. Second, with 30 to 45 days at sea from Asia to Guayaquil, Puerto Bolívar, Puerto Limón, Santa Marta or Caucedo and 3 to 4 weeks of production from artwork approval, confirm the order 10 to 12 weeks before the week the stock runs out and keep a 3-week reserve; on a farm that bags all year, the practical arrangement is an annual contract with quarterly shipments.
| # | Data point | Why it decides the price |
|---|---|---|
| 1 | Lay-flat tube size in inches or centimetres (34 × 72, 34 × 90…) and whether the bottom is open or sealed | Film area per cover |
| 2 | Gauge in mil or microns (0.4 mil = 10 µm) and tolerance | Film weight, the biggest cost item |
| 3 | Perforation: hole diameter (2, 3, 4 or 6 mm), spacing, full or partial | Perforation tooling and line speed |
| 4 | Colour of each reference (blue, white, clear, red, green) and whether colour marks the bagging week | Masterbatch and number of references |
| 5 | Treatment: untreated (what we make) or impregnated (we say so on the quotation) | Whether we can supply the cover or only the rest of the pack |
| 6 | Printing: farm or association logo, colours, faces, vector artwork and Pantone | Plates and changeovers per reference |
| 7 | Quantity per reference in pieces, rolls or kilograms (a single total with no breakdown means we have to ask again) | Run length and minimum per reference |
| 8 | Presentation: roll (covers per roll and maximum roll weight), pre-cut bundle or boxed covers | Converting and packing cost |
| 9 | Companions in the same container: foam protectors (size, thickness, colour), age ribbons, polypack liners, cluster bags, cartons | Container utilisation and freight per cover |
| 10 | Port and date: Guayaquil, Puerto Bolívar, Limón, Santa Marta, Caucedo or Davao; week the material is needed on the farm; FOB or CIF | Sailing and payment terms |
Fuxing Group makes bunch covers, polypack liners and cluster bags for bananas at four plants in Dongguan (China), Hai Phong (Vietnam) and Davao and Calamba (Philippines), with ISO 9001, ISO 14001 and FSC certification and SGS test reports: untreated bunch covers from 10 µm in 34 × 72, 34 × 90 and any size to order, perforated 2 to 6 mm full or partial, in blue, white, clear, red or green, printed with the farm logo in up to 2 colours; EPE foam bunch protectors of 3 to 8 mm from Hai Phong; polypack liners and cluster bags printed in up to 8 colours; and the 13 kg and 18.14 kg corrugated cartons that go with them. Our Davao plant supplies the bagging and packing of export programmes in the Philippines, the world's second banana origin, for brands such as Sumifru, Unifrutti and Del Monte Philippines. We quote in English or Spanish within 24 hours, send physical samples of each reference to test on your farm before the first shipment, and consolidate covers, protectors, bags and cartons in one container to Ecuador, Colombia, Costa Rica, Honduras, Guatemala, Mexico, Peru, the Dominican Republic and the Philippines.
Quote on WhatsApp Email jacky@fuxinggroup.cnOr use the quotation form · Send the 10 data points, or simply a photo of the cover you use today with its size, gauge and perforation and your farm artwork, and we return a quotation per reference with the weight per 1,000 covers.